A full water tank is one of the heaviest things on a rural property. Every litre of water weighs about a kilogram, so a big tank puts many tonnes on a small circle of ground and keeps it there for years. If the base settles or washes out, the tank can bulge, split or lean. This guide covers what the base has to do, how a concrete slab compares with a compacted pad or a stand, what the NSW approval and bush fire rules say, and how to pick and prepare the spot.
What a water tank base has to do
The base spreads the weight of a full tank over firm ground and holds its shape while the ground around it gets wet and dries out again. It has to be level across the whole footprint, so the water pushes evenly on the tank walls, and smooth enough that nothing sharp presses into the tank floor.
The tank maker’s installation guide is the starting point. It sets the size of the base, what it can be made of and how flat it needs to be. The NSW Planning Portal says exempt rainwater tank works must be structurally adequate, installed in accordance with the manufacturer’s specifications and comply with the Building Code of Australia. Following the spec sheet matters for staying exempt as well as for the warranty.
An empty tank has the opposite problem. NSW Health’s rainwater tank advice notes that plastic tanks need some water in them, or need tying down, so they don’t blow over in strong winds when they’re emptied.
Concrete slab, compacted pad or tank stand
Most rural tanks sit on one of three bases. The right one depends on the tank’s material and size, the ground under it and what the tank maker allows.
| Base | Where it suits | Ask the tank supplier |
|---|---|---|
| Concrete slab | Large tanks, concrete and steel tanks, soft or sloping ground, and spots that need to hold their shape through wet seasons. | Do you want a slab under this tank, and what finish should the top have? |
| Compacted pad | Smaller poly tanks on firm, flat, well-drained ground, usually crusher dust or road base held in by an edge ring, where the maker allows it. | What edge restraint stops the pad washing out? |
| Raised stand | Tanks that need height for gravity feed, such as a header tank above the house or a supply to stock troughs. | Who designed the stand and its footings for a full tank? |
A slab costs more up front, but it’s the base least likely to change shape. A compacted pad relies on its edging and drainage. Once water runs under it or the edge ring rots, one side starts to slump, and a lean on a full tank gets worse, not better. A tank slab is poured much like any other concrete slab on prepared ground, set out to the size the tank maker asks for.
Need a tank slab with the rest of the job?
Tank base, shed slab and driveway on one itemised quote. Free, with a reply within 24 hours.
Do you need approval for a rainwater tank in NSW?
Many rainwater tanks are exempt development, which means no council approval, as long as they meet every standard in the state policy. The Planning Portal’s rainwater tanks page says the extra standards depend on the zoning of your land, and lists places where an above-ground tank can’t be exempt at all.
- Foreshore and sensitive land. Above-ground tanks can’t be installed as exempt development in a foreshore area or an environmentally sensitive area.
- Heritage items. On a heritage item or draft heritage item, the tank has to go in the rear yard.
- Structure. The works must be structurally adequate, installed to the maker’s specifications and comply with the Building Code of Australia.
- Trees. If the spot means removing or pruning trees, check with council first.
The size, height and setback limits sit in the state policy and change with your zone, so check them against your property’s zoning before you order the tank. If the tank is part of a new house, shed or subdivision, the development consent or bush fire conditions may decide the tank for you. On most properties the tank slab is one item in a wider rural concrete job, so it’s worth settling where it goes before the other slabs are set out.
Bush fire rules that affect the tank and its slab
On bush fire prone land the tank may have a second job. Planning for Bush Fire Protection 2019, the NSW RFS document applied to development on bush fire prone land, calls for a static water supply where town water isn’t available or can’t be relied on.
For those developments it says above-ground water storage tanks shall be of concrete or metal, and that above-ground water service pipes are metal, up to and including any taps. It sets a minimum supply by lot size, including 20,000 litres per lot for large rural and lifestyle lots over 10,000 m². If your consent carries these conditions, ask the tank supplier for the base requirements of the concrete or steel tank you’re buying, because they won’t match a poly tank’s.
Access is part of it too. PBP 2019 asks for access for a Category 1 fire appliance to within 4 m of the static water supply. In practice that puts the tank beside a driveway or hardstand a fire truck can use in wet weather, which often means extending the acreage driveway or a turning area out to the tank slab. NSW Health’s bushfire advice adds the upkeep: keep the roof catchment clear of overhanging branches and remove vegetation around the tank.
Choosing and preparing the spot on acreage
Most tank base problems start with where the tank went, not how the slab was poured. Work through these before anyone digs.
- Pick firm, natural ground. Stay off filled ground, old dam walls and soft spots. A base on fill can settle on one side once the tank is full.
- Work out the levels. Gutters need to fall to the inlet, and the outlet needs to reach the house, the troughs or the fire fitting. The slope of the spot decides how much cut it takes to get a level pad.
- Plan the overflow. Overflow water needs a set path away from the slab, so it doesn’t scour the ground under the edge or run across a neighbour’s land.
- Leave room for trucks. The concrete truck or pump needs to reach the spot, and on bush fire prone land a fire truck needs to as well.
- Keep it clear of trees. Roots lift slabs and pads, and leaves end up in the water. It also makes the vegetation clearance around the tank easier to keep up.
The cost of a tank slab comes down to the slab size the tank maker asks for, how much cut or fill it takes to get level, the ground and whether rock turns up, access for the truck or a pump, edge details and drainage around the slab, and whether it’s poured on the same day as other work on the property. If the spot needs benching into a slope first, that’s site preparation work and goes on the quote as its own line.
Before the tank slab is quoted
- Tank make, size and base spec in hand
- Zoning and exempt standards checked
- Bush fire conditions confirmed
- Firm, natural ground chosen
- Inlet, outlet and overflow routes planned
- Truck access to the spot