Driveway guides

Concrete Driveway Designs: Finishes, Borders and Layouts That Work

  • LicensedNSW contractor lic. 398552C
  • $20m insuredPublic and product liability
  • 13+ yearsHands-on in the concreting trade
  • 5.0 on Google10+ five-star reviews
  • 24-hour replyFree, itemised quotes

Short answer

What is the best design for a concrete driveway?

The best concrete driveway design suits the house, the slope and how the driveway gets used. Most good designs pair one main finish, such as exposed aggregate or charcoal, with a contrasting border or band, and set the joints out so they become part of the pattern. Steeper driveways need a finish with grip.

A driveway is the biggest single surface at the front of most homes, and on a Hills block it’s usually the first thing you see from the street. Getting the design right is less about picking a pattern from a brochure and more about matching the finish to the house, the slope and the cars that use it. This guide covers the main finishes, how borders and bands are used, why joints belong in the design, and the council rules that decide what you can do at the kerb.

Start with the finish

Most concrete driveway designs are built from one main finish, sometimes with a second finish used for borders or bands. Each one looks and behaves differently, especially in the wet and on a slope.

FinishWhat it looks like and where it suitsAsk
Broom finishPlain concrete with a fine brushed texture. Clean and simple, and the grippiest of the common finishes on a slope.Will a plain finish suit the house, or does it need a coloured border?
ColouredPigment through the mix, such as charcoal, for a solid modern look that sits well with dark roofs and render.Which pigment and how much has been specified?
Exposed aggregateThe surface is washed back to show the stones. The stones set the colour and the texture.Can I see a sample of this stone and mix?
StencilledA pattern such as pavers or tiles pressed into the colour layer, with a flat, even surface.How will the pattern line up with the joints?
StampedA textured pattern pressed into the surface, often stone or slate looks.Is it grippy enough for the grade of my driveway?

Colour needs care in the specification. Cement Concrete & Aggregates Australia’s driveways and paths datasheet says the pigment supplier, colour and percentage by weight of cement need to be specified, and that coloured concrete shouldn’t be cured under plastic sheeting, damp sand or wet hessian, because they can cause uneven colour or staining. The decorative concrete finishes Southo pours all go on the same preparation underneath. Only the top changes.

Borders, bands and mixed finishes

A border is the simplest way to lift a plain driveway. A charcoal or plain grey band along the edges, across the boundary or around the garage apron frames the main finish and gives the eye a line to follow up the block. On wider driveways, bands across the width also break up a long run of the same surface.

  • Exposed aggregate field, plain border. The stone carries the colour and the smooth border gives a clean edge against lawn and garden beds.
  • Charcoal field, exposed aggregate bands. Suits modern homes with dark trims, and the bands add grip where they cross the slope.
  • Sandstone edging. Sandstone blocks along one or both sides tie the driveway into retaining walls and garden edges on a sloping block.
  • Matching paths and pool areas. Running the same finish from the driveway into the paths and entry makes the whole front read as one design.

With exposed aggregate, CCAA’s exposed aggregate briefing notes the stones usually provide the dominant colour, and the cement between them is normally coloured to match or blend with the stone. It also recommends test panels, so you see the finished result before the whole driveway goes down.

Got a look in mind for the driveway?

Send a photo of the house and the look you like. You get a free quote with every stage on its own line.

Joints are part of the design

Every concrete driveway needs joints to control where it cracks. Left to chance, they cut across a pattern or border in the wrong place. Planned well, they become part of the layout. CCAA’s driveways datasheet gives the rules most designs are built around.

  • Spacing. Control joints at maximum 3 metre centres, and at changes in shape, changes in direction and around pits or other rigid objects.
  • Panel shape. Panels roughly square, with the ratio of width to length not more than 1:1.5.
  • Angles. No angle between joints, or between a joint and the edge, of less than 75°, to avoid narrow tapered pieces.
  • Decorative work. Joints located to suit the decorative pattern or finish where possible.

That last point is where design and engineering meet. Borders and bands make good places for joints to sit, because the line is already there. On a curved driveway, joints that radiate from the curve look deliberate, while joints laid on a straight grid look like an afterthought. The joint layout belongs on the plan before anything is poured, the same as on any concrete driveway Southo quotes.

What council allows at the kerb

The design you pick usually stops at the boundary. Between the boundary and the road is council land, and the crossing there is built to council’s rules.

The Hills Shire Council’s driveway and footpath crossings page says council consent is needed for works within the road reserve, including new or replacement driveways, as a Section 138 approval under the Roads Act 1993. It says only one driveway is permitted per residential lot, and work follows council’s driveway specifications with inspections before the pour and at the end.

Hawkesbury City Council’s driveway crossing specification shows how far a decorative design can go on council land. The layback must be plain concrete, with colouring and stencilling not permitted. On the crossing slab it accepts broom, coving trowel, patterned or stamped finishes not more than 5 mm deep, and exposed aggregate with stone up to 14 mm. It also says council isn’t responsible for matching a finish other than plain concrete if the crossing is later removed.

Inside the boundary, NSW’s exempt development rules for driveways cap all driveways, paths and paving at 15% of the lot or 150 m², whichever is less, and say the driveway can’t be wider than the garage, carport or hardstand it serves. A design with a wide entry apron or a second parking pad can push past those limits.

Exposed aggregate driveway at the garage entry of a home in Winston Hills
Exposed aggregate driveway, Winston Hills

Designing a driveway for a Hills block

Hills blocks are rarely flat. Grade, curves and drainage shape the design as much as the finish does.

  1. Check the grade first. CCAA notes steep pavements need a coarse texture, and that steel trowelled, polished, stamped and smooth aggregate finishes may be unsuitable depending on the grade. Coarse broom, tined, dragged and stencilled finishes suit steeper driveways better.
  2. Plan where the water goes. Where a driveway falls toward the house, CCAA says a drain should be provided beside the building to divert the runoff. A channel drain across the garage apron can be designed in as a feature line.
  3. Shape the curves. A curve that follows the slope is easier to drive and looks better than a straight line forced up the hill.
  4. Allow for turning and parking. A turning bay or visitor pad changes the overall shape, and it counts toward the paved area limit.
  5. Tie it to the rest. Paths, steps, the entry and any pool area look best in the same or a matching finish.

The cost of a designed driveway comes down to the area, the finish and any border or band work, the old driveway coming out, excavation and base on the slope, access for the truck or pump, drainage, and the council crossing. Every Southo quote lists each of these on its own line, so a design can be compared with a plain version before you decide.

Design decisions to settle before the quote

  • Main finish and colour chosen
  • Border or band design sketched
  • Joint layout on the plan
  • Grade and grip checked
  • Drainage and apron drain planned
  • Council crossing finish confirmed

Want a driveway that suits the house?

Send a photo and the look you like. Your quote lists the finish, the borders, the crossing and every other stage on its own line.

Southo
Concrete

We are Sydney’s top choice for residential, civil, and industrial concreting services.

Get a Free Quote

Looking for reliable concrete services? Fill out the form below, and we’ll provide you with a personalised quote tailored to your project needs.


Accuracy note

Council and planning information on this page is general and was correct on 29 October 2026 against the sources named above. Rules change and every site is different, so confirm your own situation with your council. This is not advice for a specific property. Spotted something out of date? Email southoconcrete2@outlook.com.

Southo
Concrete

We are Sydney’s top choice for residential, civil, and industrial concreting services.

Get a Free Quote​

Looking for reliable concrete services? Fill out the form below, and we’ll provide you with a personalized quote tailored to your project needs.


Southo
Concrete

We are Sydney’s top choice for residential, civil, and industrial concreting services.

Get a Free Quote

Looking for reliable concrete services? Fill out the form below, and we’ll provide you with a personalized quote tailored to your project needs.